HYPACK SURVEY 2012 MANUAL
HYPACK SURVEY 2012 SOFTWARE
HYPACK SURVEY 2012 TRIAL
HYPACK SURVEY 2012 PC

Approximately 230 linear kilometers of digital Chirp subbottom (seismic-reflection) and 234-kilohertz interferometric sonar (bathymetric and backscatter) data were collected along with sediment samples, riverbed photographs, and (or) video at 88 sites within the geophysical survey area. ДЄbstract: A geophysical and geological survey was conducted at the mouth of the Connecticut River from Old Saybrook to Essex, Connecticut, in September 2012. Suggested citation: Ackerman, S.D., Foster, D.S., Moore, E.M., Irwin, B.J., Blackwood, D., and Sherwood, C.R., 2017, High-resolution geophysical and sampling data collected at the mouth of Connecticut River, Old Saybrook to Essex, Connecticut, 2012, USGS Field Activity 2012-024-FA : U.S.

HYPACK SURVEY 2012 TRIAL

Sea Trial - Commissioning Step 13 : GPS Time Delay (Required)ДЎ0.2.7.David S. Sea Trial - Commissioning Step 12: Beam Width ReductionДЎ0.2.6. Sea Trial - Commissioning Step 10: Side Lobe LevelsДЎ0.2.4.Sea Trial - Commissioning Step 11 : Sound SpeedДЎ0.2.5. Commissioning Step 7: Tide ConfigurationДЎ0.2Sea Trials.49ДЎ0.2.1.Sea Trial - Commissioning Step 8: Array PolarityДЎ0.2.2.Sea Trial - Commissioning Step 9 : Roll Correction PolarityДЎ0.2.3. Commissioning Step 6: Heading (Yaw) OffsetДЎ0.1.8. Commissioning Step 5: Electrical NoiseДЎ0.1.7. Commissioning Step 1: Ship MeasurementsДЎ0.1.3.Commissioning Step 2: Channel GainДЎ0.1.4.Commissioning Step 3: Channel Signal FunctionДЎ0.1.5.Commissioning Step 4: Array GeometryДЎ0.1.6.

HYPACK SURVEY 2012 SOFTWARE

25Д§.5 WASSP Software Operation.26ДЁ.1 NMEA Interconnection.28ДЁ.2 Supported Sentences.29ДЁ.3 WASSP Transfer Task Settings.30Д©.1 Hypack Integration.32Д©.1.1 Configuration.32Д©.1.2 Software Configuration Basics.34Д©.1.3 Data Collection.36ДЎ0.1Commissioning Procedures.

HYPACK SURVEY 2012 PC

21Д§.1 WASSP PC Dimensions.23Д§.2 WASSP PC Mounting Considerations.24Д§.3 WASSP PC Connections.24Д§.4 Software Installation.25Д§.4.1 User Dongle. 9ДҐ.2 Transducer Dimensions.10ДҐ.3 Transducer Mounting Methods.11ДҐ.3.1 Through Hull Mounting.11ДҐ.3.2 Pole Mounting.12ДҐ.4 Transducer Mounting Considerations.13ДҐ.4.1 Transducer Mounting вЂ“ General Considerations.13ДҐ.5 Gland Assembly.14ДҐ.5.1 Mount the Transducer Cable Gland.14ДҐ.5.2 Transducer cable Installation.16Д¦.1 BTxR Connections and Dimensions.18Д¦.2 BTxR Installation.19Д¦.2.1 BTxR Installation Considerations.19Д¦.2.2 BTxR Installation.19Д¦.2.3 Power to BTxR. в–єв–є Make sure that the transducer will not loosen due to theДЄ CAUTION indicates that if the instructionДЄ Note indicates a tip or additional information that could beДў.1 Main Features. These to be carried out in accordance with local or national regulatory body safety regulations. в–єв–є Make sure all safety precautions for electrical equipmentДЄre taken when operating or servicing the equipment. Result in loss of life or serious injury. Instruction is not heeded, the action may Warnings, cautions, and notes are indicated by the в–єв–є Do not open equipment covers unless you are totallyДЇamiliar with the systemвЂ™s electrical circuits. switchboard) before beginning the installation.ДЇire or electrical shock may occur if the power is left ON. в–єв–є Make sure that the power is switched OFF at the main в–єв–є The equipment is rated for operation at: в–єв–є Fire, electrical shock, or equipment damage may occur if

HYPACK SURVEY 2012 MANUAL

Of this manual and any system specifications withoutД¬ontact WASSP Ltd. reserves the right to change the contents WASSP Ltd.ДЄssumes no responsibility for any damage associated The correct installation of the equipment. The installer of the equipment is solely responsible for Update of Hydrographic Software Installation Update of Sea Trial Commissioning Step 13

Hypack survey 2012